Menu
Your Cart

Micro Hardness Tester

Micro Hardness Tester

Material hardness

Different techniques are used to quantify material characteristics at smaller scales. Measuring mechanical properties for materials, for instance, of thin films, can not be done using conventional uniaxial tensile testing. As a result, techniques testing material "hardness" by indenting a material with a very small impression have been developed to determine to estimate these properties.

Hardness measurements quantify the resistance of a material to plastic deformation. Indentation hardness tests compose the majority of processes used to determine material hardness, and can be divided into two classes: microindentation and macroindentation tests. Microindentation tests typically have forces less than 2 N (0.45 lbf). Hardness, however, cannot be considered to be a fundamental material property. Classical hardness testing usually creates a number which can be used to provide a relative idea of material properties.[2] As such, hardness can only offer a comparative idea of the material's resistance to plastic deformation since different hardness techniques have different scales.

The main sources of error with indentation tests are poor technique, poor calibration of the equipment, and the strain hardening effect of the process. However, it has been experimentally determined through "strainless hardness tests" that the effect is minimal with smaller indentations.

Surface finish of the part and the indenter do not have an effect on the hardness measurement, as long as the indentation is large compared to the surface roughness. This proves to be useful when measuring the hardness of practical surfaces. It also is helpful when leaving a shallow indentation, because a finely etched indenter leaves a much easier to read indentation than a smooth indenter.

The indentation that is left after the indenter and load are removed is known to "recover", or spring back slightly. This effect is properly known as shallowing. For spherical indenters the indentation is known to stay symmetrical and spherical, but with a larger radius. For very hard materials the radius can be three times as large as the indenter's radius. This effect is attributed to the release of elastic stresses. Because of this effect the diameter and depth of the indentation do contain errors. The error from the change in diameter is known to be only a few percent, with the error for the depth being greater.

Another effect the load has on the indentation is the piling-up or sinking-in of the surrounding material. If the metal is work hardened it has a tendency to pile up and form a "crater". If the metal is annealed it will sink in around the indentation. Both of these effects add to the error of the hardness measurement.

The equation based definition of hardness is the pressure applied over the contact area between the indenter and the material being tested. As a result hardness values are typically reported in units of pressure, although this is only a "true" pressure if the indenter and surface interface is perfectly flat.

Microindentation tests

The term "microhardness" has been widely employed in the literature to describe the hardness testing of materials with low applied loads. A more precise term is "microindentation hardness testing." In microindentation hardness testing, a diamond indenter of specific geometry is impressed into the surface of the test specimen using a known applied force (commonly called a "load" or "test load") of 1 to 1000 gf. Microindentation tests typically have forces of 2 N (roughly 200 gf) and produce indentations of about 50 μm. Due to their specificity, microhardness testing can be used to observe changes in hardness on the microscopic scale. Unfortunately, it is difficult to standardize microhardness measurements; it has been found that the microhardness of almost any material is higher than its macrohardness. Additionally, microhardness values vary with load and work-hardening effects of materials. The two most commonly used microhardness tests are tests that also can be applied with heavier loads as macro indentation tests:

In micro indentation testing, the hardness number is based on measurements made of the indent formed in the surface of the test specimen. The hardness number is based on the applied force divided by the surface area of the indent itself, giving hardness units in kgf/mm². Micro indentation hardness testing can be done using Vickers as well as Knoop indenters. For the Vickers test, both the diagonals are measured and the average value is used to compute the Vickers pyramid number. In the Knoop test, only the longer diagonal is measured, and the Knoop hardness is calculated based on the projected area of the indent divided by the applied force, also giving test units in kgf/mm².

The Vickers micro indentation test is carried out in a similar manner welling to the Vickers macroindentation tests, using the same pyramid. The Knoop test uses an elongated pyramid to indent material samples. This elongated pyramid creates a shallow impression, which is beneficial for measuring the hardness of brittle materials or thin components. Both the Knoop and Vickers indenters require pre-polishing of the surface to achieve accurate results.

Scratch tests at low loads, such as the Bierbaum microcharacter test, performed with either 3 gf or 9 gf loads, preceded the development of microhardness testers using traditional indenters. In 1925, Smith and Sandland of the UK developed an indentation test that employed a square-based pyramidal indenter made from diamond. They chose the pyramidal shape with an angle of 136° between opposite faces in order to obtain hardness numbers that would be as close as possible to Brinell hardness numbers for the specimen. The Vickers test has a great advantage of using one hardness scale to test all materials.The first reference to the Vickers indenter with low loads was made in the annual report of the National Physical Laboratory in 1932. Lips and Sack describes the first Vickers tester using low loads in 1936.[

There is some disagreement in the literature regarding the load range applicable to microhardness testing. ASTM Specification E384, for example, states that the load range for microhardness testing is 1 to 1000 gf. For loads of 1 kgf and below, the Vickers hardness (HV) is calculated with an equation, wherein load (L) is in grams force and the mean of two diagonals (d) is in millimeters:

For any given load, the hardness increases rapidly at low diagonal lengths, with the effect becoming more pronounced as the load decreases. Thus at low loads, small measurement errors will produce large hardness deviations. Thus one should always use the highest possible load in any test. Also, in the vertical portion of the curves, small measurement errors will produce large hardness deviations.

Multi‐functions Motorized Turret Touch Screen Digital Micro Vickers Hardness Tester
Brand: Metallography World CorporationModel: HT‐1AT‐8P
MULTI FUNCTION MICRO VICKERS HARDNESS TESTER (4 VARIATIONS TESTER)   Introduction & Features: The traditional Micro hardness tester has poor precision and can barely meet the needs of visual observation & measurement. If connect with camera and softwar..
Multi‐functions Manual Turret Touch Screen Digital Micro Vickers Hardness Tester
Brand: Metallography World CorporationModel: HT‐1MT‐8P
MULTI FUNCTION MICRO VICKERS HARDNESS TESTER (4 VARIATIONS TESTER)   Introduction & Features: The traditional Micro hardness tester has poor precision and can barely meet the needs of visual observation & measurement. If connect with camera and softwar..
Multi‐functions Motorized Turret Touch Screen Digital Micro Vickers Hardness Tester
Brand: Metallography World CorporationModel: HT‐1AT‐8
MULTI FUNCTION MICRO VICKERS HARDNESS TESTER (4 VARIATIONS TESTER)   Introduction & Features: The traditional Micro hardness tester has poor precision and can barely meet the needs of visual observation & measurement. If connect with camera and softwar..
Multi‐functions Manual Turret Touch Screen Digital Micro Vickers Hardness Tester
Brand: Metallography World CorporationModel: HT‐1MT‐8
MULTI FUNCTION MICRO VICKERS HARDNESS TESTER (4 VARIATIONS TESTER)   Introduction & Features: The traditional Micro hardness tester has poor precision and can barely meet the needs of visual observation & measurement. If connect with camera and softwar..
6 Positions Motorized Turret Double Indenter Digital Micro Vickers Knoop Hardness Tester
Brand: Metallography World CorporationModel: HT‐DVK‐1A‐6
6 POSITIONS TURRET DIGITAL MICRO VICKERS KNOOP HARDNESS TESTER     Main Function: HT-DVK-1A-6 Digital Micro Vickers and Knoop hardness tester is a high-tech and new product combining the optics, mechanic and electrics features. With a novel and pleasin..
XYZ  Automatic Precision Micro Hardness Tester - 1kgf
Brand: Metallography World CorporationModel: HT-APMC-1-XYZ
Overview HT-APMC-1-XYZ a XYZ Automatic Precision Micro Hardness Tester - 1kgf automatic precision microhardness tester, based on the mechanical principle of the positive quadrilateral pyramid diamond indenter into the sample surface to produce indentation. By measuring the diagonal length of the ind..
Intelligent Digital Micro Vickers Hardness Tester
Brand: Metallography World CorporationModel: HT‐DVS‐1AT
      INTELLIGENT DIGITAL MICRO VICKERS HARDNESS TESTER     Main Function: This instrument is a new generation of Micro Vickers hardness tester. It adopts the in..
XYZ  Automatic Precision Micro Hardness Tester - 50kgf
Brand: Metallography World CorporationModel: HT-APMC-50-XYZ
Overview HT-APMC-50-XYZ automatic precision Vickers hardness tester, based on the the mechanical principle of positive quadrilateral pyramid diamond indenter into the sample surface to produce indentation. By measuring the diagonal length of the indentation to achieve the hardness of the material me..
Intelligent Fully Automatic Micro Vickers Hardness Testing System with Computer System
Brand: Metallography World CorporationModel: HT‐DVS‐1XYZ
FULLY AUTOMATIC MICRO VICKERS HARDNESS TESTER      HT-DVS-1XYZ Fully Automatic Micro Vickers Hardness Tester is integrated with several new technologies such as optical imaging, mechanical displacement, electronic control, digital imaging, image analysis, compute..
Micro-Dimensional Hardness Tester
Brand: Metallography World CorporationModel: HT-VCK-MD
Overview HT-VCK-MD microhardness tester, based on the principle that positive quadrangular pyramid diamond indenter presses the surface of the sample to produce indentation. By measuring the diagonal length of the indentation to achieve the measurement of the hardness of the material can be for smal..
Automatic Turret Micro Hardness Tester
Brand: Metallography World CorporationModel: HT-VCK-ATM
Overview HT-VCK-ATM micro hardness tester, based on the principle that positive quadrangular pyramid diamond indenter presses the surface of the sample to produce indentation. By measuring the diagonal length of the indentation to achieve the measurement of the hardness of the material can be for s..
Intelligent Fully Automatic Micro Vickers Hardness Testing System
Brand: Metallography World CorporationModel: HT‐DVS‐1XYZ‐I
INTELLIGENT FULLY AUTOMATIC MICRO VICKERS HARDNESS TESTER     Main Function: This instrument is a new generation of automatic Micro Vickers hardness tester. It adopts the integrated design of hardness tester and panel computer; With Windows 7 operating..
Showing 1 to 12 of 14 (2 Pages)